Créer mon blog M'identifier

FORD VCM.

Le 28 novembre 2016, 04:38 dans Humeurs 0

Although it was autumn, the weather is still hot. Under high temperature, the car to bear a high load operation, mechanical wear and aging tired than usual a lot worse... So, today Xiaobian to introduce several car maintenance tips, check it out!
1, interior to often clean, sterilization
High temperature many owners do not often open windows, and in order to air conditioning wind, and often only choose the inner loop. A long time, the car will become particularly turbid air, then, the interior will be particularly vulnerable to the breeding of bacteria. So, be sure to regularly clean the interior, in order to ensure the fresh air in the car.
You can buy some of the interior cleaning agents to clean, you can also go to the car beauty shop to carry out a thorough cleaning of the interior.
2, engine maintenance
We should try to choose some high viscosity oil, because the viscosity of oil will change with the increase of temperature. When the temperature is higher, the viscosity of oil will be decreased, the oxidation resistance becomes worse, and the oil film formed in the engine is thin and uneven, which is easy to cause trouble.
In addition, in order to ensure the sufficient lubrication conditions, should be based on the use of the range of temperature, the temperature of the engine and the actual condition chooses the corresponding viscosity lubricating oil.
3, to prevent the car from spontaneous combustion
High temperature and hot weather is also a high incidence of auto ignition accident. Spontaneous combustion of the car will not only cause economic losses, but also may cause casualties, need to pay more attention to. There are many reasons to cause the spontaneous combustion of automobile, such as engine fuel filter, line fault, power line aging and so on.
4, explosion-proof tires
Due to the higher temperature inside the tire pressure is high, the weather is hot, too high or too low tire pressure is easy to cause the tire abnormal heating moment expansion burst, so we must pay special attention to frequently check the tire pressure, which were maintained within the normal range.
In addition, in the long time driving or high speed tire easily overheat, but pressure increased, this time should stop heat, no gas pressure or water cooling.
Ford-VCM OBD Diagnostic Interface High Quality
Ford-VCM OBD Diagnostic Interface is professional device for ford vehicles, Ford-VCM OBD has the most functions of ford vcm ids, it is the mini version of ford vcm ids. Ford-VCM OBD works on ford car by OBD2 port directly.
It is designed for ford, mazda and other few brand cars, really working very well with those cars 1996-2010, some 2011 cars.
Ford-VCM OBD is diagnostic programmer for Ford vehicles 1996-2010. It can connect to various electronic control units (ECUs) and display identification, read and clear fault code memory, display and record measured values and perform actuator tests, some key programmer, etc.
You can go to GO2OBD.NET buy FORD VCM.

FGTECH Galletto 2 Master Tunning Tool

Le 28 novembre 2016, 03:13 dans Humeurs 0

Daily car maintenance is directly related to the life and safety of the vehicle, if the car maintenance may be improper for the driver and passengers to bring a lot of security risks. Therefore, as a qualified owner, usually learn a few strokes of the car maintenance tips or very useful. Here are some of the maintenance of common sense, we want to help.
1, belt inspection
Start the car engine or in the process of driving the car, found that the belt ring, the reason is divided into two kinds: one is the belt has not adjusted for a long time, found in a timely manner to adjust. Another reason is the belt aging, need to replace the new belt.
2, air filter inspection
Air filter too dirty or blocked, will directly lead to increased fuel consumption, poor work and so on. Regular check the air filter, if found less dust, the blockage is not serious, can be used with high pressure air from the inside out of the net, continue to use, and over the dirty air filter should be replaced in a timely manner.
3, check the gasoline filter
If the oil supply is not found, should be timely check the fuel filter is blocked, found that the plug should be promptly replaced.
4, engine coolant level inspection
Wait for the engine to cool down, check the coolant level should be between full and low, if not, please immediately add distilled water, purified water or frozen liquid, the liquid level can not exceed the full. If the hair is a rapid decrease in the cooling fluid within a short period of time, it should be checked whether there is a leak or to the special car store inspection.
5, tire inspection
Tire pressure directly related to the safety performance of the tire, the tire pressure is too high or too low will cause bad results, high temperature in summer, the tire pressure should be low, the winter temperature is low, the tire pressure should be enough. Also check the tire cracking, the existence of security risks should be timely replacement tires, in the selection of new tires, tire model consistent with the original.
FGTECH Galletto 2 Master Tunning Tool Plus BDM AdaptorsFGTech Galletto 2 Master BDM-TriCore-OBD Plus BDM adaptors is a famous chip tuning tool for all cars, trucks, motorcycles, Marine, BDM MPCxx, BDM Boot Mode Tricore, checksum. This item cannot only work as FGTech Galletto 2 Master, but can also work for BDM-TriCore-OBD. This FGTECH Galletto 2 is with BDM adaptors make job so easy.
You can go to GO2OBD.NET buy fgtech.

MB Star C3.

Le 24 novembre 2016, 03:51 dans Humeurs 0

Daily car maintenance is very important. A slight effect on daily maintenance will not only cause unnecessary damage to the vehicle, but also endanger the safety of traffic. On the contrary, if the daily work done carefully, not only can make the vehicle to maintain a regular new, but also to avoid traffic accidents. In fact, the daily maintenance work is very simple, simple is: clean, tighten, check, supplement.
One, clean
The air contains a lot of dust, sediment and acidic substances, not only easy to leak oil adhesion, easy to form the high temperature baking insulating layer hard, the heat dissipation performance of parts of the variation, and it is prone to electrostatic adsorption and the erosion of the body paint, paint and oxide.
We should not only pay attention to the general clean car paint clean, also want to pay attention to the car interior, car engine, car air conditioning and cleaning wheel etc..
Two, fastening the vehicle after cleaning, it is to be on the connection of the fastening. Due to vibration, bumps and swing of the dry line, the connection piece is bound to be loose and wear. Therefore, in the daily maintenance should be timely tightening. The connecting piece fastening daily work is directly related to traffic safety, especially the important parts of steering, braking, transmission, must not be let down. If the engine around the joint of the hose to tighten, anti oil leakage. Secondly, fasten all the lines and connectors for electric equipment, electric equipment to work normally prevent open circuit and short circuit and ground effect etc.. Again, the main connection parts for inspection and fastening, such as the generator drive belt, steering linkage brake device connection point, the transmission system and tires, etc..
Three, check the connection parts, should check the oil liquid height and quality, because the liquid at high temperature will gradually loss and oxidation and lead to lower level of the liquid and performance change. 1, check the battery level.
With a diameter of 5 N 6mm tubes from the liquid inlet and the vertical force to screen after contact is closed with the thumb of the lift tube tube, measuring the height of liquid column is the battery level, standards should be 10 N 15mm. 2, check the oil level height of the car cold dipstick out, wipe, into oil pan bottom, after observing the height between the upper and lower line. The car should be stalled, the oil into the oil pan after measurement. 3, check the coolant level the height of the car cold cooling liquid in the tank is full, the expansion tank level should be in line. The hot liquid height should be slightly higher than. 4, check the brake fluid, liquid level to unscrew the bolts, direct observation of liquid level in the specified range of markings. 5, check the quality of oil, whether it is the oil, can use the following methods to check.
(1) the appearance of law: check oil samples taken, if more transparent, not that serious pollution; if a fog, while oil seeps in the water; if a grey, may be lead or other abrasive contamination; if is black, it is polluted by high temperature exhaust gas. (2) diffusion method: a drop of oil samples will be taken on the filter paper, if the diffusion is very wide and there is no obvious difference between the oil droplets and the diffusion zone, it shows that the oil is clean and good.
Mercedes Benz MB Star C3 Diagnosis With Latest Software
1.This is the Mercedes MB STAR C3 Diagnose Tool works on Car 12V and Heavy Duty 24V.
2. It has real PCB in RS232-485 cable.
3. The price is with 120GB hard drive which include Xentry,DAS,WIS,EPC,SDMedia,StarFinder ect.
4.High Quality Compact 3 Star Diagnosis Tool with 2 years warranty.
You can go to GO2OBD.NET buy MB Star C3.

Voir la suite ≫